Cisco 7960

[dll2002dll]

Hi Guys,

I am having issues configuring my Cisco 7960 phone with VBuzzer, i am running the latest SIP firmware from Cisco 8.7. The Cisco phone is connected to Linksys WRT54G running DD-WRT. I have no issues using VBuzzer software and Linksys PAP2. I have also tried connecting my phone directly to the Internet without a router, it is also not working.


If people call my number it goes to voice mail "the party you're to reach is unavailable please leave a message and someone will return your call as soon as possible." Also if I try to dial out I get a fast busy (also tried dialing 101#, getting fast busy as well).


Here are my settings.

Settings->SIP Configuration->1 Line 1 Settings

1. Name: Name
2. Shortname: Shortname
3. Authentication Name: <VBuzzer Username>
4. Authentication Password: <VBuzzer Password>
5. Display Name: Display Name
6. Proxy Address: vbuzzer.com
7. Proxy Port: 80

Settings->SIP Configuration-> 1 to 7 Unchanged
8. Preffered Codec: g711ulaw
9. Out of Band DTMP: avt (I think avt=auto)
10. Register with Proxy: yes
11. Register expires: 3600
12. TFTP directory: <leave empty>
13. Phone Label: <UNPROVISIONED>
14. Enable VAD: No
15: VoIP Control Port: 5060
16: Start Media Port: 16384
17: End Media Port: 32766
18: Backup Proxy:
19: Backup proxy port: 5060
20: Emergency proxy:
21: Emergency proxy port: 5060
22: Outbound Proxy: N/A
23: Outbound Proxy port:
24: NAT Enabled: Yes
25: NAT Address: N/A
26: Call Statstics: No

Anybody has any luck configuring Cisco7960 phone with VBuzzer.

[voipcaller]

I've never tried configuring that device but I think that in the sip settings, the voip control port should be changed to port 80.

[dll2002dll]

I tried that already, if I change it to 80 it will revert back to 5060. Basically I tried setting it lower than or equal to 1023, it will not take it. Anything 1024 and higher is only acceptable in the settings..

Anyother workarounds?

[Pearl]

I have tested this configuration, it works great. I am using SIP ver6.0 firmware.

[3]Network Setup
3.1 DHCP Server: 192.168.0.1 (your default network gateway)
3.5 IP address: 192.168.0.101
3.6 Subnet Mask: 255.255.255.0
3.9 Default Router1: 192.168.0.1
3.14 DNS Server 1: 192.168.0.1
3.23 Network Media Type: Auto
3.24 Network Port 2 Device Type: PC
3.25 DHCP Enable: Yes
3.29 HTTP Proxy Addr: vbuzzer.com
3.30 HTTP Proxy Port: 80

[4]SIP Configuration
4.1 LIne 1 Settings
4.1.1 Name: vbuzzerusername
4.1.2 Shortname: vbuzzerusername
4.1.3 Authentication Name: vbuzzerusername
4.1.4 Authentication Password: vbuzzerpassword
4.1.5 Display Name: vbuzzerusername
4.1.6 Proxy Address: vbuzzer.com
4.1.7 Proxy Port: 80

4.8 Preferred Codec: g711ulaw
4.9 Out of Band DTMF: avt_always
4.10 Register with Proxy: YES
4.11 Register Expiress: 30
4.14 Enable VAD: YES
4.15 Voip Control Port: 5060

4.22 Outbound Proxy: vbuzzer.com
4.23 Outbound Proxy Port: 80
4.24 NAT Enable: YES
4.25 NAT Address: 192.168.0.1 (or your router WAN port IP address)
4.26 Call Statistics: YES

[dll2002dll]

I followed your instructions, I am getting a fast busy when I try to dial out.

[dll2002dll]

I actually gave it another try, reset the phone to factory default and followed your instructions verbatim (thats the key), and it did work actually.

Thanks for the help.

[cgigate]

I have used 7960 for a year with one line of Vbuzzer, it works great!
_________________
We make VOIP work.
Many pre-configured Vbuzzer adapter for sale.

[red6apple]

How did you reset the Cisco phone to factory default? I have followed the settings, but I can only dial out, and cannot receive calls.

Thanks.

[bybunny]

I am having same problem on cisco 7960, can dial out but cannot receive calls.
Any help will be much appreciated.
thanks

[admin]

We do not have the CISCO 7960 in hand.
Regarding incoming calls, we just remind: Please do not use buzzme DID number in the configuration. Please use your vbuzzer account instead because our system routes a call based on vbuzzer account.

[alex6999]

another problem with cisco
phone didn't hung up automatically.

[Haxi]

Thanks for taking the time to help, I really apprciate it.

[admin]

According to a test log from one customer, the firmware P0S3-8-12-00 (i.e. 8.12) has a bug about NAT.

Please downgrade to firmware P0S3-8-2-00 (i.e. Version 8.2). It will work.

This is applied to both Cisco 7960 and Cisco 7940.